SPN 4364 FMI 3AftertreatmentMedium
SCR NOx Efficiency Sensor - Voltage High
Scan Tool — in guided session
DVOM Testing — in guided session
Connector Pinout — in guided session
DieselVision™ Upload photos — DieselVision™ reads diagrams, connectors, and screens with precision.
Overview
Fault Code
SPN 4364 / FMI 3
Category
Aftertreatment
Severity
Medium
Derate Risk
Sometimes
Regen Inhibit
No
Inducement Risk
No
Component Location: Downstream NOx sensor is mounted on the SCR outlet cone or exhaust pipe downstream of the SCR catalyst, typically toward the rear underside of the vehicle.
Common Symptoms
- SCR NOx efficiency fault active in ECM
- MIL or amber warning lamp illuminated
- DEF system warning active
- Possible inducement or derate condition
- NOx sensor reading implausibly high or out of range
Root Causes
- Failed or internally shorted downstream NOx sensor supplying voltage above sensor range Damaged or chafed wiring harness causing short to voltage on signal circuit Corroded or moisture-contaminated sensor connector Faulty NOx sensor heater circuit interaction causing signal voltage spike Failed NOx sensor control module or gateway ECU ECM internal fault on NOx sensor input circuit
Full step-by-step tests, DVOM guidance, and pinout data are available inside the AI Diesel Tech diagnostic session.
AI walks you through every test — one step at a time. Plans start at $12.95/mo.
Derate Behavior
Power Derate
Sometimes
Mileage / Regen Notes
Sensor circuit issue — check wiring before replacing sensor.
System Interactions
SPN 4364 FMI 3 interacts with the following systems and may trigger cascading faults if not resolved promptly.
DPF differential pressure monitoring — soot load calculations affected
SCR NOx conversion efficiency — DEF dosing strategy may be altered
Active regen inhibit logic — regen may be blocked or delayed
Engine protection derate — ECM may reduce power to protect components
TSB Reference: Efficiency sensor TSB
Common Diagnostic Mistakes
Replacing the sensor without verifying wiring continuity and supply voltage first.
Clearing codes without identifying and resolving the root cause — the fault will return.
Ignoring related active faults — cascading faults often share a root cause.
Skipping the connector inspection — corrosion and damaged pins are a leading cause of sensor faults.
Condemning the ECM before exhausting all wiring and component tests.
Replacing the DPF without verifying the regen system is functional — a failed regen injector will reload the new DPF.
Ignoring DEF quality — contaminated DEF causes SCR efficiency faults that look like hardware failures.
Related Faults in This Category
OEM System Resources
ASE Training Resources
Diagnostic Engine v7.0
Related Diagnostic Articles
Deep-dive diagnostic page: SPN 4364 FMI 3 — Full FSM Sequence & Repair Steps — includes wiring notes, sensor specs, and gated repair procedures.
Authority References
Diagnostic procedures on this page are informed by OEM service literature and industry standards.
EPA Aftertreatment & Emissions GuidelinesU.S. EPA heavy-duty diesel aftertreatment compliance, DPF/SCR regulations, and NOx standards.Cummins QuickServe OnlineOfficial Cummins service manuals, fault code lookup, and TSB database.Detroit Diesel DiagnoCentralDetroit Diesel diagnostic procedures, DDDL documentation, and service literature.PACCAR MX Engine ServicePACCAR MX-11 and MX-13 engine service documentation and DAVIE diagnostic guides.Volvo/Mack Tech ToolVolvo and Mack engine fault code reference and PTT/Tech Tool diagnostic procedures.ASE — Diesel Truck Technician CertificationNational Institute for Automotive Service Excellence — T2 Diesel Engines certification standards.
Get weekly diesel diagnostic tips
Real-world fault code walkthroughs, wiring tips, and shop-tested fixes — free.
No spam. Unsubscribe anytime.
Get AI-Guided Diagnosis for SPN 4364 FMI 3
The diagnostic engine walks you through every physical test — step by step, on your phone, at the truck. No guessing. No wasted parts.